Home » News » In the News » What Should Engineers Consider When Designing DC-Coupled Charging Stations?

What Should Engineers Consider When Designing DC-Coupled Charging Stations?

Views: 0     Author: Site Editor     Publish Time: 17-11-2026      Origin: Site

facebook sharing button
twitter sharing button
linkedin sharing button
whatsapp sharing button
sharethis sharing button
What Should Engineers Consider When Designing DC-Coupled Charging Stations?

A charging station is no longer always a collection of independent chargers connected to an AC distribution system.

As charging power increases, some system designers are exploring DC-coupled architectures that connect EV chargers, battery storage, and renewable energy sources through a shared DC bus.

The idea is attractive.

Instead of converting power between AC and DC multiple times, certain energy sources and loads can exchange power through a more direct DC architecture.

But integrating everything around a common DC bus also creates new engineering requirements.

For charging station integrators, the biggest challenge is not simply connecting the equipment. It is making sure the system can operate safely under different power conditions.

Start with the architecture, not the contactor

Imagine an EV charging station with:

- Multiple DC charging modules.

- An on-site battery energy storage system.

- A photovoltaic power source.

- A grid-connected AC/DC converter.

- A shared DC bus.

During normal operation, power may come from the grid, the battery system, or solar generation.

When several vehicles charge simultaneously, the power demand can change rapidly.

At other times, the battery system may absorb excess energy or support charging demand.

This means that the DC bus is not serving just one load. It is connecting several power sources and conversion systems.

A DC-coupled charging station can reduce conversion stages in certain configurations, but it also requires careful consideration of protection, control, and system coordination.

NREL Docs+1

Four design considerations

1. Understand the power flow under different operating modes

The first step is to map how power moves through the system.

For example:

Operating condition Possible power flow

Normal charging Grid → DC bus → EV

Peak charging demand Grid + battery → DC bus → EV

Solar generation available PV → DC bus → EV / battery

Low charging demand Grid / PV → battery charging

The actual architecture will depend on the converter topology and control strategy.

However, this simple exercise helps engineers identify which branches require switching and isolation.

It also helps determine whether a contactor must support current flow in one direction or both.

2. Define the isolation requirements for each branch

A shared DC bus should not mean that every component must be disconnected together.

Suppose one charging module requires maintenance.

Ideally, the system design should allow that branch to be isolated without unnecessarily shutting down the entire charging station.

The same consideration applies to battery storage and other DC-connected equipment.

Engineers should determine:

- Which branches require independent isolation?

- Which switching devices are used during normal operation?

- Which protective devices interrupt fault currents?

- What happens if a branch develops an electrical fault?

This is where contactor selection becomes part of the broader system design.

3. Consider voltage, current, and load characteristics together

A charging station may operate at a high DC bus voltage, but this does not mean every contactor in the system has identical requirements.

A battery branch, charging module, and converter connection may experience different current profiles.

Engineers should evaluate:

- Maximum operating voltage.

- Continuous current.

- Peak and transient current.

- Load inductance.

- Required breaking capacity.

- Switching frequency.

A contactor selected only because its rated current matches the expected load may not be suitable for the actual switching duty.

4. Plan for maintenance and future expansion

Charging stations are long-term infrastructure projects.

The initial system may contain only a few charging modules, but the operator may add more chargers or increase storage capacity later.

If the original DC bus and protection architecture cannot accommodate expansion, upgrading the system may require significant redesign.

Planning for modular isolation and clear maintenance procedures can make future changes easier.

A practical example: adding battery storage to an existing charging station

Consider an integrator that initially designs a grid-connected fast-charging station.

Later, the customer requests battery storage to reduce peak grid demand.

The battery is connected to the DC side through a bidirectional converter.

The original charging system may still operate, but the addition changes the power flow and protection requirements.

The integrator now needs to review the battery connection, switching arrangement, fault isolation, and control coordination.

The contactor specification should be reviewed as part of this change rather than selected independently from the rest of the system.

The contactor is one part of a larger design decision

For charging station manufacturers, the most effective approach is to define the system architecture first and select switching components according to their actual position and duty.

ESTAR DC contactors can be considered for suitable high-voltage DC switching applications, subject to verification of the required operating and interruption conditions.

You can also read our article about the contactor inside an electric vehicle to understand how DC contactors are used in another high-voltage application.

  • No. 8, Changyu Road, Chang'An, Shijiazhuang, Hebei, 050015 China
  • Call us on:
    +86-13315914545
Leave a Message
Send Us A Message